Chimney Repair in Aurora, CO | Morningstar Chimney Sweep

Chimney Repair in Aurora - Inspected on Camera, Then Priced in Writing

Liner and masonry work is where this trade gets a bad name, so nothing is quoted until you have seen the camera footage yourself. Then a written, itemized price with no scope creep.

Call to schedule your free estimate

Work is performed by our local vetted partner.

Free
Written Quotes
Licensed & Insured Written Quotes Free Estimates All Brands Satisfaction Guarantee

Work is performed by our local vetted partner.

Sweep & inspectionSweep & inspection
Caps & crownsCaps & crowns
Flue reliningFlue relining
Masonry repairMasonry repair
Gas fireplace serviceGas fireplace service
Every visit starts with

Level 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed

Worth knowing

Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.

Get your free estimate

Trusted Chimney Repair for Aurora Homeowners

Chimney problems in Aurora rarely announce themselves. A hairline crack in the crown, a rusted damper, or flashing that pulled loose in a spring windstorm can let water into the masonry for months before you notice a stain on the ceiling. We fix those problems before they turn into a rebuild. Our technicians have up to 8 years of experience, and every job starts with a documented inspection so you know exactly what we found and why it matters.

professional chimney repair service in Aurora, CO

Call (855) 368-2029

Morningstar Chimney Sweep handles the sweep, the inspection, and chimney repair as one company, so nothing gets handed off to a separate contractor halfway through. We work with professional-grade materials from DuraFlex, HeatShield, Gelco, Olympia Chimney, Famco, and Copperfield, not hardware-store patches. When a repair can wait, we say so. When it can’t, we explain why in plain terms. Call (855) 368-2029 to book an estimate and get a clear account of what your chimney needs.

Chimney Cap Installation

Chimney Cap Installation is the single most cost-effective step a homeowner can take to keep water, animals, and debris out of the flue. A properly fitted cap sits on a mesh or louvered frame that lets smoke and gases escape while blocking rain from running straight down the chimney. In Aurora, where summer hail and fall leaf drop are both hard on an open flue, a cap pays for itself by preventing the corrosion and nesting problems that drive bigger repairs later. We install caps sourced through Gelco and Famco product lines, the same supply chain commercial chimney contractors use, and we size the cap to your actual flue opening rather than forcing a universal fit. Our technicians have up to 8 years of experience fitting caps on brick, stucco, and prefab chase chimneys across the metro. Typical chimney cap installation in Aurora runs $250-$600, depending on flue count and cap material.

Single-Flue and Multi-Flue Fitting

A single-flue cap is straightforward, but homes with a fireplace plus a furnace flue in the same stack need each opening capped separately so neither one breathes into the other. We measure every opening before ordering. That avoids the return trip that stalls a job halfway through.

Stainless and Powder-Coated Options

Stainless caps hold up best against the freeze-thaw cycling that Aurora chimneys see every winter. Powder-coated steel can look sharper on a visible chimney face and still performs well when the gauge is heavy enough. We’ll tell you which one fits your flue and exposure, and we won’t push the pricier option if the standard one does the job.

Explore

Styles & brands we work with

  • Sweep & inspection
  • Caps & crowns
  • Flue relining
  • Masonry repair
  • Gas fireplace service

Chimney Cap Replacement

Chimney Cap Replacement is what a cap needs once it’s rusted through, lost its mesh, or blown loose in a wind gust. A damaged cap is worse than no cap at all: it funnels water into the flue, and a loose cap can let birds or squirrels drop nesting material onto the smoke shelf. If you’ve found rust flakes in the firebox or seen daylight through the mesh from below, the cap has failed. We remove the old cap and frame, inspect the flue tile beneath for cracking, and install a replacement from Gelco or Famco sized to the existing opening. We don’t reuse a rusted frame to save a few dollars, because that’s the part that fails first. Typical chimney cap replacement in Aurora runs $200-$500, depending on whether the mounting frame and flue tile are still sound.

Spotting a Failed Cap

Look for a cap sitting crooked, mesh that’s torn or missing, or rust staining the crown below it. Those are the three signs we see most often on Aurora roofs. Any one of them means the cap is no longer doing its job.

When the Frame Comes With It

Older caps are often bolted to a frame that’s rusted at the weld points, and that’s a replacement rather than a re-mount. We check the frame before quoting so the number you get is the number that holds. Nobody wants a surprise line item on the invoice.

Chimney Liner Installation

Chimney Liner Installation restores the barrier between the hot flue gases and the combustible structure of your house. A clay tile liner that has cracked, spalled, or separated lets heat and carbon monoxide reach framing, and that’s a problem no amount of sweeping fixes. We install DuraFlex flexible stainless liner systems, the industry standard for safe, code-compliant relining, sized to your appliance and chimney height. For liners that are damaged but not collapsed, we can resurface with HeatShield, a specialist-only repair system that extends chimney life without the cost of a full reliner. Not every flue is a candidate for resurfacing; the camera inspection tells us which path is right. “Do I really need a new liner?” is the question we hear most, and the honest answer is no more often than you’d think. Call (855) 368-2029 for an exact quote, estimates are free.

Flexible Stainless Relining

DuraFlex liner is pulled down an insulated chimney and secured at the top plate, and it works on offsets and irregular flues that rigid pipe can’t handle. We size the liner to the appliance, since an oversized flue runs cool and collects creosote faster. It’s one of the details that separates a liner that lasts from one that needs replacing in a decade.

HeatShield Resurfacing

HeatShield is applied by trained applicators and restores a deteriorated liner from the inside, rebuilding the flue surface without removing the existing tile. It’s a good fit when the tile is cracked but the structure is still sound. It’s not a shortcut for a collapsed flue, and we’ll say so if that’s what the camera shows.

Chimney Flashing Repair

Chimney Flashing Repair addresses the metal at the base of the chimney where it meets the roof, which is the most common leak point on any home with a masonry stack. Flashing is stepped into the shingles and sealed into the brick, and when that seal fails, water runs down the chimney chase and shows up as a ceiling stain far from the actual leak. Aurora’s freeze-thaw swings work flashing loose season after season, and the hail that rolls off the Front Range dents and separates the metal. We reset or replace flashing, re-step it into the shingle courses, and seal the brick course properly so water sheds away instead of wicking in. Typical chimney flashing repair in Aurora runs $300-$700 depending on roof pitch and how much shingle work is involved. Masonry cracks often show up alongside flashing failures, which is why we check both on the same visit.

Leaks That Aren’t the Roof

Homeowners often call a roofer first when the stain shows up, and the roofer points at the chimney. We confirm where the water is actually entering before anyone cuts into shingles. That saves a roofing bill for a chimney problem.

How Flashing Should Sit

Proper flashing has a base, step sections woven into the shingles, and a counter-flashing set into a reglet cut in the brick. When a repair skips the counter-flashing, the seal fails within a few seasons. We install the full assembly, not just the visible part.

Chimney Crown Repair

Chimney Crown Repair fixes the concrete cap at the very top of a masonry chimney that sheds water away from the brick below. Hairline cracks in the crown are normal, but once a crack widens, water freezes in it, expands, and pushes the crown apart until it’s directing water into the chimney instead of off it. That’s when you get spalling brick and rusted damper assemblies well below the roofline. We repair crowns with a proper mortar mix and slope, or rebuild a crown that’s past patching, so the top of the chimney actually sheds water the way it’s supposed to. Repairing a crown costs far less than rebuilding the top of a chimney that rotted from the inside out. Typical chimney crown repair in Aurora runs $400-$1,200 depending on the size of the crown and whether it can be resurfaced or needs a rebuild. Sometimes a cap installation is the better fix for water getting down the flue.

Cracked vs. Failed

A crown with a few hairline cracks can often be sealed and resurfaced. A crown that’s crumbling, separated from the flue tile, or sloping toward the flue rather than away from it needs to be rebuilt. We make that call from the roof, not from a photo.

Why the Slope Matters

A crown should slope down and away from the flue on all sides so water leaves the chimney rather than pooling at its base. Many failed crowns were poured flat. We build in the slope as part of the repair.

Chimney Repair Companies

Chimney Repair Companies vary widely in what they actually do, and that’s the first thing to sort out before you hire one. Some outfits sweep and leave, some subcontract every repair, and some handle the whole life cycle of the chimney in one place, which is what Morningstar Chimney Sweep does: sweep, inspection, and repair under one roof. You want a company that documents what it finds with a camera inspection and photo report you can see for yourself, and that won’t recommend thousands of dollars of work you have no way to verify. You also want one that says plainly when a repair can safely wait. Our inspection reports are built to be handed to an insurer, a real-estate agent, or a local fire marshal. Typical chimney repair pricing in Aurora spans $200-$3,500 depending on scope, and the written estimate sets the final number.

Questions Worth Asking

Ask whether the sweep, inspection, and repair are done by the same company or handed off. Ask to see photos of what was found before anyone quotes a liner. Ask what can wait. A straight answer to that last one tells you more than any brochure.

Specialist vs. Generalist

A general handyman can patch masonry, but a chimney has specific draft, liner, and clearance requirements that a generalist may not be equipped to assess. We stay in our lane: chimneys only. That focus is why the diagnosis holds up.

Professional chimney technician applying mortar repair to a cracked chimney crown in Aurora, CO

Chimney Masonry Repair

Chimney Masonry Repair rebuilds the brick and mortar that take the worst of Aurora’s weather on every home with a masonry stack. The freeze-thaw cycle along the Front Range is hard on mortar joints: water soaks in during a warm afternoon, freezes overnight, and pushes the joint apart a little more each time. Spalled brick faces, crumbling mortar, and white efflorescence staining are all signs water is winning. We repoint joints, replace spalled brick, and rebuild chimney sections that have lost structural integrity, matching the existing brick where possible. Masonry repairs are also where we look hardest for the real source of water entry, because a repointed chimney that still leaks is money wasted. Typical chimney masonry repair in Aurora runs $500-$2,500 depending on the number of courses involved and whether a rebuild is needed.

Repointing vs. Rebuilding

Repointing replaces the mortar between sound bricks and is the right call when the brick itself is intact. Rebuilding is necessary when brick faces have spalled deep enough that the unit can’t hold mortar. We tell you which one your chimney needs, and why.

Matching the Existing Brick

A repaired chimney should look like it was never touched. We match brick size, color, and mortar joint profile wherever the supply allows, rather than dropping in whatever’s on hand. On a visible chimney face, that difference matters.

Brands We Service

We install and service DuraFlex flexible liner systems and know where the liner wears thin first: the top plate and the transition at the appliance flue collar. HeatShield resurfacing is a specialist-only product, and we apply it when the tile is damaged but the structure has enough life left to make resurfacing the smarter call than a full reliner. We fit Gelco and Famco chimney caps and covers, sourced through the same professional supply chain commercial chimney contractors use. Olympia Chimney and Copperfield components come up in relining work often enough that we know how their fittings mate with the appliances we see across Aurora.

We’re not a dealer for any of these brands, and we won’t tell you a brand name alone makes a job good; the sizing and installation do. But we do work with these product lines daily, which means we’re not learning the fit on your roof. Whether you have DuraFlex, HeatShield, Gelco, Olympia Chimney, Famco, or Copperfield components in your chimney, or any other make, we can help.

Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Signs You Need a Pro Right Now

  • A crack in the firebox or flue tile. A cracked firebox brick or a visible gap in the flue tile lets heat reach framing and gases escape into the house. Don’t burn until it’s looked at, because the fix is usually simpler when it’s caught early.
  • Water stains on the ceiling or chimney chase. A brown ring on the ceiling near the chimney usually means flashing or crown failure, not a roof leak. Left alone, that water rots the framing and the liner behind the brick.
  • White staining on the brick. Efflorescence is the chalky white residue left when water moves through masonry and evaporates. It’s a reliable sign the chimney is taking on water somewhere, and it’s worth finding out where.
  • Rust on the damper or firebox. Rust means moisture is getting in, whether from a failed cap, crown, or flashing. A rusted damper can seize and stop sealing, which changes how the fireplace drafts.
  • A smell of smoke or soot in the house when the fireplace isn’t lit. That’s often backdraft from a blocked or damaged flue, and it’s a sign the chimney needs a camera inspection before the next fire. It’s not always urgent, but it’s never something to leave unexamined.

Our Process, Step by Step

  1. 1
    Book the visit. Call (855) 368-2029 and we’ll schedule a time that works for you. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday. We’re closed Saturdays.
  2. 2
    Inspect before we sweep. We run a camera down the flue before cleaning so we’re not sweeping over a crack we can’t see. What the camera shows sets the plan, and you get photos of what we found.
  3. 3
    Explain what we found, in plain terms. We’ll walk you through the condition report and show you the evidence, and we’ll tell you what can wait and what can’t. Nothing gets recommended that the photos don’t support.
  4. 4
    Quote the job in writing. The written estimate sets the price, per job, with the scope laid out. You decide before any work starts, and there’s no pressure to bundle in extra repairs.
  5. 5
    Do the repair, then show you the result. We install with the same professional materials we stock, whether that’s a DuraFlex liner or a HeatShield resurfacing, and we leave you with a clear account of what was done and what, if anything, still needs attention.

How Much Does Chimney Repair Cost in Aurora?

Chimney repair in Aurora typically runs $200-$3,500 depending on what’s wrong and how far the damage has gone. A cap replacement or flashing repair usually lands at the low end, while a reliner or a masonry rebuild sits at the top. Here’s how the common repairs break down:

  • Chimney cap replacement: $200-$500
  • Chimney cap installation: $250-$600
  • Flashing repair: $300-$700
  • Crown repair: $400-$1,200
  • Masonry repair: $500-$2,500
  • Liner installation or HeatShield resurfacing: quoted per flue after inspection

What moves the number: the number of flues involved, roof pitch and access, whether the repair is a resurface or a full rebuild, and whether you’re working on a masonry chimney or a prefab chase. A prefab chase that’s lost its cap is a quicker, cheaper fix than a masonry stack that needs repointing.

How to avoid overpaying: get a written estimate with the scope spelled out, ask for photos of what was found before work is recommended, and ask the company what can safely wait. A repair that can wait a year and one that can’t look identical on an invoice, but they’re not. Our inspection includes a documented condition report you can hand to an insurer or a real-estate agent, so you’re not deciding on faith alone.

What’s included in a free estimate: a camera inspection, a condition report with photos, and a written scope with pricing. The estimate is free, and there’s no charge to find out what your chimney actually needs. Call (855) 368-2029 for an exact quote, estimates are free.

Our Service Area Near Aurora

We work across Aurora and the surrounding communities, including Four Square Mile, Holly Hills, Meridian, Sierra Ridge, Acres Green, Stepping Stone, Bennett, Castle Pines, Todd Creek, Strasburg, and Ponderosa Park. Whether you’re in a brick home in Holly Hills with a stack that’s seen forty winters, or a newer build in Sierra Ridge with a prefab chase, we handle the same sweep-inspect-repair process. For homeowners just outside the city, we also cover chimney repair in Four Square Mile and chimney repair in Holly Hills, plus Meridian and the eastern communities along the metro edge. Call us to confirm scheduling for your address. Distances vary, so we’ll book you into the next opening that fits your area.

Serving Aurora, CO – Our Local Coverage Area

We serve Aurora and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.

Frequently Asked Questions About Chimney Repair in Aurora

Schedule Your Chimney Repair Service in Aurora Today

If you’re unsure whether your chimney needs a fix or just a sweep, that’s exactly the kind of question a documented inspection answers. Morningstar Chimney Sweep handles the sweep, the inspection, and the repair as one company, with professional-grade materials and a condition report you can see for yourself. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. Call (855) 368-2029 for a free, no-obligation estimate and a clear account of what your chimney needs.

Written by the team at Morningstar Chimney Sweep.

Looking for the full picture on how we handle Morningstar Chimney Sweep services? Start here.

Why Aurora Chooses Morningstar Chimney Sweep

We set the standard for chimney repair in Aurora.

Evidence Before Recommendations

Every sweep includes a camera inspection and a photo report. If we find something, you see it before we quote it - no repair is ever recommended on our word alone.

Licensed & Insured

Fully certified technicians who meet all local and state licensing requirements.

Upfront Pricing

No hidden fees, no surprises. You approve the price before any work begins.

Guaranteed Work

Every repair and installation is backed by our workmanship warranty and satisfaction guarantee.

How It Works in Aurora

Getting your chimney repair handled is simple and fast.

1

Call or Request a Free Estimate

Tell us about your chimney repair needs and we provide an upfront, transparent quote with no obligation and no hidden fees.

2

We Book a Time That Works for You

A background-checked, certified technician arrives at the time we agree on.

3

Problem Solved, Guaranteed

We complete the job to your full satisfaction, backed by our warranty and satisfaction guarantee.

What happens when you call

  1. 1
    A real person answersNo phone trees. Talk to a local chimney repair pro.
  2. 2
    You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
  3. 3
    We come out and measureLicensed & insured, at a time that suits you. The visit and the quote are both free.
  4. 4
    You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.

What Aurora Customers Say

Trusted by homeowners across Aurora and surrounding areas.

★★★★★

"Swept it, capped it, and installed a proper damper. The downdraft smell in the summer that we'd lived with for years is gone."

Brian Ziegler
★★★★★

"Fair price, competent work. The guy wasn't especially chatty and I had to ask twice to get a real explanation of what he'd done. Not a dealbreaker, just noting it."

Dale Kowalski
★★★★★

"Fireplace had never drawn properly since we moved in. He found the damper was only opening halfway due to a bent linkage and fixed it in ten minutes."

Yusuf Karam

Ready for Chimney Repair in Aurora?

Call now for a free estimate, or request one below. Licensed, insured, and here with fast help in Aurora.

(855) 368-2029

Request a Free Estimate in Aurora

Tell us about your chimney repair needs. We'll respond within the hour.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Prefer to text? Text Now
Local Service Coverage
Call Now - We Answer 24/7