Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Sweep for Aurora Homeowners
Creosote builds up quietly. A fireplace that drafts fine in November can start smoking or smelling like tar by January, and the glazed, sticky layer that causes it doesn’t come off with a brush from the hardware store. A professional Morningstar Chimney Sweep visit answers the two questions most Aurora homeowners actually have: how much buildup is in the flue, and is it safe to keep burning. Our technicians have up to 8 years of experience, and we inspect before we sweep so you see what we found instead of taking our word for it. Call (855) 368-2029 to book. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.

Chimney Sweep Services
Chimney Sweep Services from Morningstar Chimney Sweep cover the full picture: a thorough cleaning, a visual condition check, and a written account of what we found in the flue, firebox, and cap. You need this when you’ve burned a full season or more since the last cleaning, when you notice smoke rolling back into the room, or when you’re buying a home in Aurora and need a credible report for the file. A standard sweep in Aurora typically runs $150-$350, depending on how much creosote has built up, the flue configuration, and whether a cap or damper needs attention. The written estimate sets the final price, and nothing is added without your approval.
What a Standard Sweep Covers
We clean the flue with rods and brushes sized to your liner, then clear the firebox and smoke shelf of soot and debris. We also remove ash from the firebox floor and check the damper operates freely. Every sweep ends with a look at the cap and crown so you know whether weather is getting in.
When to Schedule a Sweep
Once a year is the common benchmark for a fireplace in regular use, and more often if you burn hard or burn softwood. In Aurora’s dry, high-desert air, flues can dry out and crack, so an annual look catches deterioration early. Book before burning season starts rather than after the first cold snap.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Chimney Cleaning
Chimney Cleaning is the deeper pass: removing soot, creosote, and any glaze that has hardened onto the liner walls. You need it when a sweep turns up a sticky, tar-like layer that a standard brush won’t lift, when you’ve been burning unseasoned wood, or when a prior owner left the flue neglected for years. Cleaning in Aurora typically runs $180-$400, with heavier glaze landing at the upper end because it takes more time and different tooling. We use rotary cleaning equipment matched to your flue type, and we bag and remove the debris so nothing ends up on your living room floor.
Creosote Stages Explained
Creosote moves from loose and flaky to crusty to glazed and glassy, and each stage is harder to remove than the last. Glazed creosote is the one worth stopping early, since brushing alone won’t get it. If we find it, we’ll show you and explain the options before any work is quoted.
What We Do Differently
We lay drop cloths, use a contained vacuum system, and work from the flue down rather than tracking soot through the house. We also inspect as we clean instead of saving that for a separate visit. One company handles the sweep, the inspection, and the repair, so there are no handoffs.
Fireplace Cleaning
Fireplace Cleaning addresses the part you see every day: the firebox, the grate, the glass doors, and the masonry around the opening. You need it when soot has darkened the firebox walls, when smoke stains creep onto the facing stone or brick, or when an open hearth has filled with ash over the season. Fireplace cleaning in Aurora generally runs $120-$250 as part of a sweep, or more if smoke staining has set into the masonry and needs careful treatment. We clean the firebox to bare surface, clear the ash pit, and check the damper seal while we’re in there.
Soot and Smoke Staining
Soot is acidic, and left on masonry it holds moisture and stains the stone. We remove it without scrubbing procedures that would dull or scratch the surface. If staining has soaked in, we’ll tell you honestly what can and can’t be lifted.
Ash Pit and Damper Checks
A full ash pit blocks airflow and makes the fire harder to control. We clear it and confirm the cleanout door seals properly. The damper gets tested open and closed so you know it will shut tight when the flue is cold.
Chimney Services
Chimney Services at Morningstar are built around three things: inspection, sweeping, and repair, all handled by the same crew on the same call. You need the full scope when a sweep turns up more than soot, like a cracked crown, a missing cap, a rusted damper, or a deteriorated liner. Rather than sending you to a second contractor, we diagnose, document, and fix. Repairs range widely by job, so they’re quoted individually after we’ve seen the flue; what we won’t do is quote thousands of dollars of work without photo evidence you can look at yourself. DuraFlex flexible liner systems and Gelco chimney caps are among the materials we work with.
Sweep, Inspect, and Repair Together
Coordinating two companies for one chimney usually means paying twice for access and losing time waiting. We plan the work so the sweep, the inspection, and any repair happen in the same visit where possible. You get one clear account at the end.
Documented Findings
Every job produces a record of what we saw and what we did. That report is what you hand to an insurer, a real-estate agent, or a fire marshal when they ask about the chimney. Clarity from the first call to the final invoice.
Chimney Sweep Certified
Chimney Sweep Certified means the person on your roof follows recognized industry practice for cleaning, inspecting, and evaluating a flue, and that matters at resale, at insurance renewal, and after a chimney fire. You need certified-level work when a lender, insurer, or buyer asks for proof the chimney was properly serviced. Morningstar’s technicians have up to 8 years of experience and are trained on the professional materials the trade specifies, including HeatShield resurfacing systems. A certified sweep in Aurora typically runs $150-$350, with inspection documentation included. We frame code questions as general best-practice guidance and point you to your local building department for specifics.
What Certification Means in Practice
Trained technicians know the difference between a flue that’s merely dirty and one that’s failing. They also know how to read a crown, a smoke chamber, and a cap for the small failures that turn into repairs. That judgment is the value, not a certificate on a wall.
Inspections You Can Hand Over
Our chimney inspections produce a documented condition report you can present to insurers, agents, or your local fire marshal. It describes what we found in plain terms, with photos where they help. No jargon you have to decode.
Gas Fireplace Cleaning
Gas Fireplace Cleaning covers the venting and burner assembly on a gas unit, which needs attention even though it never sees wood smoke. You need it when the flame has gone from blue to yellow, when the logs show soot or white deposits, or when the fireplace hasn’t been looked at since it was installed. Gas fireplace cleaning in Aurora typically runs $130-$280, depending on the unit and how much of the assembly needs disassembly. We check the venting, clear debris from the burner ports, and confirm combustion looks the way it should. Gas lines are not a do-it-yourself item, so leave anything past a visual check to us.
What Gas Cleaning Involves
We clean the glass, the logs, and the firebox interior, then check the vent termination and cap for blockage. Debris in the vent is one of the more common reasons a gas unit starts running poorly. We test the way it draws once it’s back together.

Reading the Flame
A healthy gas flame is mostly blue with a steady shape. Yellow tips or lifting flames can point to an air or venting problem. We note what we see and explain whether it needs a closer look.
Chimney Maintenance
Chimney Maintenance is the annual routine that keeps a working chimney from becoming a repair project: a sweep, a condition check, and small fixes done before they grow. You need it every year if you burn at all, and especially in a place like Aurora where dry air and winter freeze-thaw cycles work on masonry over time. Maintenance-level visits typically run $150-$350, with any repairs quoted separately after we’ve seen them. Famco and Gelco caps and covers are part of the routine here, since a proper cap keeps rain and animals out between visits and reduces how often repair is needed at all.
The Annual Check
We look at the crown, the flashing, the cap, and the liner, since those are the failure points that show up before the interior does. A small crack in the crown is cheap to address and expensive to ignore. Anything we recommend comes with the photos to back it up.
Weatherproofing Between Visits
A correctly fitted cap does most of the work of keeping water out of a flue. We source caps and covers through Gelco and Famco product lines, so the components match the flue they’re sitting on. It’s a small addition that extends the life of the chimney.
Brands We Work With
We work with DuraFlex flexible liner systems, the industry standard for safe, code-compliant chimney relining, and we know where those liners wear and where installs tend to fail. We also apply HeatShield resurfacing, a specialist-only repair system that restores a deteriorated flue liner without full liner replacement, a capability most generalist cleaners can’t offer. When we recommend a repair, it’s because the material is right for the job and we’re trained on it.
Olympia Chimney products and Gelco caps round out the roster, and each one comes from the same professional supply chain that commercial chimney contractors rely on rather than a hardware-store substitute. We don’t stock generic parts and call them professional. Whether you have a DuraFlex liner, an Olympia Chimney component, or any other make, we can help.
See the difference
Before
After
Before
After
Before
AfterSigns You Need a Pro Right Now
- Smoke rolling back into the room. A fireplace that used to draft and now smokes is telling you the flue is restricted or the pressure has changed. It won’t fix itself, and burning through it makes the buildup worse.
- A strong tar or campfire smell when the fire is off. That odor is creosote off-gassing, and it often means a layer has built up enough to notice. It’s a sign to get the flue looked at before the next fire.
- Black or brown staining on the exterior masonry. Staining on the outside of a chimney usually means moisture is getting in or smoke is escaping where it shouldn’t. Both point to a failing crown, cap, or flashing.
- Visible cracked or missing mortar and flue tiles. Cracks in the flue liner let heat and gases reach combustible parts of the structure. This is one of the few chimney issues worth treating as urgent.
- A yellow or flickering gas flame. On a gas unit, an off-color flame can indicate incomplete combustion or a venting problem. Stop using it and have it checked.
Our Process, Step by Step
- 1
We ask questions first. Before anyone gets on the roof, we ask what you burn, how often, and what you’ve noticed. That shapes what we look for and keeps the visit focused on your actual chimney.
- 2
We protect the room. Drop cloths go down, and we set up a contained vacuum system so soot stays in the flue and out of your house. Cleaning a chimney shouldn’t leave you cleaning the living room.
- 3
We inspect, then sweep. We look at the flue, firebox, smoke chamber, cap, crown, and damper before cleaning, because the condition tells us what tooling the job needs. We use rods and brushes matched to your liner type.
- 4
We document what we found. Photos and a written condition report go with the job, so you have a record you can keep or hand to someone else. If something needs repair, we show you what and why.
- 5
We tell you what can wait. Not every finding needs work this week. Some things can safely wait a season, and we’ll say so plainly instead of pushing a repair you don’t need yet.
How Much Does Chimney Sweep Cost in Aurora?
A typical chimney sweep in Aurora runs $150-$350, depending on how much creosote has built up, how accessible the flue is, and whether the job includes a cap or damper fix. A gas fireplace cleaning usually lands between $130-$280, and a deeper creosote cleaning runs $180-$400 when glaze has to be removed. Repair work is quoted individually after inspection, since a cracked crown and a failed liner are very different jobs.
What moves the price: the stage of creosote, the number of flues, whether the chimney is on a steep roof, and whether heavy staining needs treatment. What keeps it from climbing is booking before the buildup gets bad, and having the cap in place so water stays out. We don’t quote off a phone description alone. The inspection comes first, then the written estimate, and the estimate sets the final price. Nothing gets added without your say-so.
To avoid overpaying, ask any chimney company to show you what they found before they recommend work. If a company tells you the liner is shot without evidence you can see, get a second opinion. Nothing we recommend comes without camera evidence or photos you can review for yourself, and we’ll tell you when a repair can safely wait. Call (855) 368-2029 for an exact quote. Estimates are free.
Our Service Area Near Aurora
We serve Aurora and the surrounding communities, including Four Square Mile, Holly Hills, Meridian, Sierra Ridge, Stepping Stone, Bennett, Strasburg, Todd Creek, and Ponderosa Park. Scheduling is handled when you call, and response times depend on the route and the season, with most bookings handled within a few days. If you’re in one of the outlying towns, mention it when you call so we can plan the visit. For a closer look at work in a neighboring area, see our chimney sweep page for Four Square Mile and our chimney sweep page for Holly Hills.
Serving Aurora, CO – Our Local Coverage Area
We serve Aurora and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Chimney Sweep in Aurora
A chimney sweep is a professional cleaning of the flue, firebox, and smoke chamber to remove soot and creosote. It’s not just brushing: a sweep also includes a visual check of the liner, cap, crown, and damper, and a written account of what was found. In Aurora, a sweep typically costs $150-$350 depending on buildup. Call (855) 368-2029 for an exact quote.
Most standard sweeps take 45 minutes to an hour and a half. The time depends on how much creosote has built up, how many flues the chimney has, and whether anything turns up that needs repair. If we find a problem mid-job, we stop and explain it before continuing. Call (855) 368-2029 to book a time.
A chimney sweep in Aurora typically runs $150-$350, and creosote cleaning runs $180-$400. Gas fireplace cleaning is usually $130-$280. The written estimate, given after inspection, sets the final price, and nothing is added without your approval. Call (855) 368-2029 for an exact quote. Estimates are free.
Yes. We work with DuraFlex flexible liner systems and Olympia Chimney components, along with Gelco caps and HeatShield resurfacing. We know where those materials wear and how they should sit in a flue. Whether you have one of those or any other make, we can help.
Same-day service is often possible depending on the schedule and the route. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening. Call (855) 368-2029 to check availability.
Repair and installation work is backed by a satisfaction guarantee, and specific warranty terms are put in writing with the estimate so you know what’s covered. We spell out the terms on the estimate before any work begins. Call (855) 368-2029 to ask about coverage for your job.
Clear the area in front of the fireplace, move anything breakable from the hearth, and don’t light a fire for at least 24 hours before we arrive so the flue is cool. If you know when the chimney was last cleaned, have that ready. That’s all you need to do. Call (855) 368-2029 with any questions beforehand.
Schedule Your Chimney Sweep Service in Aurora Today
Your chimney works hard. We make sure it works safely. Book a sweep with Morningstar Chimney Sweep and you’ll get a cleaning, an inspection, and a clear written account of what we found, all on one visit. Call (855) 368-2029 for a no-obligation estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Morningstar Chimney Sweep.